Information about the new tunning
verzion modul VERT+12 for HITEC R/C Transmitter Eclipse 7
Actualization: May
10 2007
VERT
+12 is universal modul which may be used for both, older PPM and the latest
QPCM Eclipse 7 transmitter.
What is diference between VER 12 and VERT +12 ?
In VERT +12 are corrected known mistakes of HELI program, whitch cause discontinuity in trottle, pitch and mixing functions.
VERT +12 enable free switch assignments for mixes and functions. Choice switches or VR trimes for free channels.
Extend number of saving models from 7 to 22. Eclipse 7 storage these models in transmitter, not to the
program modul. ROM modul is not for back-up models. COPY and RESET are
functions for all 22 models of course. If Your transmiter has smal SMD memory – only 8 models
are available.
Analogue of RESET is function SAVE in the special servis menu,
which reset all 22 models and rewrites model names to default ACRO-0, HELI-0 or
GLID-0 according to our request. In addition it saves calibration values off
control sticks.
After changing program modul
and initialization are data of all 22 models deleted.
Changed is controlling the Timer
The left key Off switch over displaying Timer or others.
When Timer is visible, right key Start/Stop
switch between following modes.
In the First mode Start/Stop Timer is controlled
by middle position of the throttle stick. In this mode is timer after switching
on the Transmitter. For GLID models is Timer controlled by motor switch or VR
button. It depends on choice of INPUT SEL CH 3.
Second mode is permanently running Timer
independently of throttle.
We can reset Timer when Timer is visible by
pressing Clear button. After Transmitter is switching on, the Timer is
automatic cleared. Operating time on the right is cleared by Clear key when
Timer is not visible.
After past setup time, Timer no stop at 0:00,
but continue run and display from setup time up to max 59:59 + 19h .
On the every hour is to hear short beep.
There are added some new mixes for acro and heli.
Programmable mixers are added by SET PMXn
There
are extended choice of MAS SLV till number 8. MAS 8 is neutral or assign
actuator in INPUT SEL CH 8. VERT +12 have chance add for acro and glid PMX
offset. It is similar to SET for CROW and F>A, F>E functions.
It is executed slow-motion for trottle servo CH 3
Servo
move constand speed 100 % approx 2 s. We can it twice speed up by switch selected
for FAST in menu set sw. We can select for FAST On (permanent without switch).
Because no exist eightchannel QPCM receiver, for two next function we must inhibit one from not-used channel.
In HELI SWAH is added function fo 90°
swashplate
This
function release transmit the 8th channel for the 4th servo of swashplate. It
is shown on the picture on the right.
For the
8th channel are also adjustable S.TRM, EPA and REV values.
For acro and glid is added choice 2ELV- two servo
for elevator
This
function release transmit the 8th channel for left elevator servo. Right servo
remain in CH2.
To switch on added AILV mix
for acro, we can select any switch in menu S/W
SEL. Left and right side of elevator will move consistently or oposite with
aileron dependency of sign in AILV value.
Choice of transmit the 8th channel for PPM
receiver
If we don’t use SWAH 90 or 2ELV functions, we may select
transmit of the 8th channel to any switch or VR knob in INPUT SEL CH 8 menu. It
is added option MIX, which mean transmitting the neutral value. This value is
usable for mixing with PMX functions.
Choice tranmitting channels for PPM receiver
It is added in setup menu SEND elimination of any channels
from transmitting. We may choice receiver with less channels after eliminating
unused chanels.
Function
DELAY for smooth switching Flight Mode
It is added in menu S/W SEL. Elimination of any channels
from DELAY is implemented. We may choice Delay from 0 to 6.3 s by tutn
ower any of seven switch.
For acro is added pair function for CH5-7
or CH7-8
This
function facitilate use two servos for flaps because PMX for pairs are
implemented too.
For acro is also added pair CH3-5 or CH3-5-7
for two or three motors
This
function facitilate use two or three servos or regulators.
For acro is added LAND for CH5 and CH7
For acro is added FLPN for CH7 too
Jiří
Palík